screening

    Mesh Size Chart: US Sieve Sizes Converted to Microns

    U.S. Chemical Services / NBN Powder Packaging October 1, 2026 5 min read

    Why mesh numbers confuse people

    Mesh size is one of those specs that looks simple until you have to act on it. A customer asks for product "through 100 mesh." A supplier's sheet says "-40/+100." A screen catalog lists wire diameter and percent open area. All three describe particle size, and none of them says it in microns, which is the unit most lab instruments actually report.

    The short version: a mesh number counts the openings in one linear inch of screen. A 20 mesh screen has 20 openings per inch. A 200 mesh screen has 200. More openings per inch means smaller openings, so a higher mesh number always means a finer cut. The trap is that the opening size also depends on how thick the wire is, which is why standards exist to pin each mesh number to a fixed opening.

    Mesh size chart: US standard sieve to microns

    The table below follows the US Standard Sieve Series defined in ASTM E11, which is what most North American labs and screen suppliers mean when they say "mesh." Openings are nominal.

    US meshOpening (mm)Opening (microns)
    44.754750
    82.362360
    102.002000
    161.181180
    200.850850
    300.600600
    400.425425
    500.300300
    600.250250
    800.180180
    1000.150150
    1200.125125
    1400.106106
    2000.07575
    2700.05353
    3250.04545
    4000.03838

    Two quick rules of thumb fall out of the chart. Doubling the mesh number roughly halves the opening (100 mesh is 150 microns, 200 mesh is 75). And 400 mesh, at 38 microns, is about where woven wire screening runs out of road for most production work. Below that you are usually in air classification or jet milling territory, which we covered in our guide to micronization and jet milling.

    Reading plus and minus notation

    Spec sheets use a shorthand that trips up new buyers. A minus sign means the material passed through that screen. A plus sign means it was retained on it.

    • -100 mesh means everything passed a 100 mesh screen, so all particles are under about 150 microns.

    • +40 mesh means the material stayed on a 40 mesh screen, so the particles are larger than about 425 microns.

    • -40/+100 describes a band: passed 40, retained on 100. In microns that is roughly 150 to 425.

    Most real specs also carry a tolerance, such as "95% min through 100 mesh." That tolerance matters as much as the number. A spec with no stated percentage is an argument waiting to happen between buyer and supplier.

    Mesh number is not the whole spec

    Two screens can share a mesh number and behave differently on the production floor. Wire diameter changes the open area, and open area changes throughput. A heavier wire lasts longer on abrasive minerals but passes less material per hour. A finer wire gives more open area and more capacity, then tears sooner. Market grade, mill grade, and tensile bolting cloth are all sold at the same mesh counts with different wire, so if a process depends on a specific screen, write down the opening in microns and the wire gauge, not just the mesh.

    Particle shape matters too. Needles and flakes can slip through an opening lengthwise that a sphere of the same "size" could not. That is one reason two labs running the same nominal mesh can report slightly different results on platy pigments or fibrous additives.

    Other mesh standards you will run into

    Tyler mesh is an older US series that tracks closely with ASTM E11 in most of the common range, and plenty of legacy specs still cite it. ISO 3310 is the international standard and labels sieves by aperture size in microns or millimeters instead of a mesh count, which honestly avoids most of this confusion. If a customer overseas sends a spec in microns and your domestic supplier quotes in mesh, convert through microns rather than trying to match mesh numbers across standards.

    Turning a mesh spec into finished product

    Knowing the chart is the easy half. Getting a production lot to meet "-60/+200, 95% min" means picking the right screens, the right number of decks, and the right feed rate so fines do not blind the cloth. Our chemical screening and classification service runs multi-deck vibratory screeners with 1 to 5 cuts per pass, which yields up to six classified fractions from a single run. When we do not have a screen size in stock, we can usually source it within 3 business days.

    If you need to confirm where a lot actually lands before or after processing, sieve testing gives you documented, fraction-by-fraction results. Our sieve analysis explainer walks through how that test works and how to read the report.

    Frequently asked questions

    What does mesh size mean?

    Mesh size is the number of openings per linear inch of a screen. A higher mesh number means more, smaller openings, so 200 mesh separates finer particles than 50 mesh.

    How many microns is 100 mesh?

    Under the US Standard Sieve Series (ASTM E11), a 100 mesh screen has a nominal opening of 150 microns, or 0.150 mm.

    Is a higher mesh number finer or coarser?

    Finer. Mesh counts openings per inch, so as the number goes up the openings get smaller. 400 mesh is about 38 microns, while 20 mesh is about 850 microns.

    What does -100 mesh mean on a spec sheet?

    It means the material passed through a 100 mesh screen, so the particles are smaller than about 150 microns. A plus sign, such as +100, means the material was retained on the screen.

    Can you screen powder to a custom mesh size in Ohio?

    Yes. US Chemical Services in Elyria, Ohio screens powders and formed materials with 1 to 5 cuts per pass and can usually source a screen size not in stock within 3 business days.

    What is the finest mesh used for production screening?

    Woven wire screening is common down to about 325 to 400 mesh, which is 45 to 38 microns. Finer separations usually call for air classification or jet milling.

    Need help with your chemical processing project?

    Talk to our team today. Most projects start within 48 hours of receiving materials.

    Back to all articles
    Request a Quote